The MFZpro-200 Professional Side-Shift Flail Mower delivers true “one mower” capability for tractors that need more coverage per pass, built for 55–80 HP with CAT I (CAT II bushings included) three-point hitch. With a 78.7″ working width and 20.5″ hydraulic side-shift, you can mow further to the right of the tractor—making it easy to work around trees, fence posts, and signs without constantly steering the tractor.
The MFZpro series is especially suited for fruit and wine growing, nurseries, and any property where prunings and woody residue are on the ground and need to be mulched. It can be used effectively on medium areas with growth up to ~39.4″ that may only need mowing a few times per year. Woody material up to 2″ (50 mm) is reliably shredded by forged, toothed hammer flails (MFZpro-200 uses 16 flails, about 2.6 lb each).
Power flows through a reinforced Comer free-wheel gearbox and a 4-belt drive into a fast, smooth rotor (2295 RPM) supported by SKF bearings in CNC bearing seats with stainless grease nipples for quick service. MFZpro also includes replaceable counter blades and a rear service gate to improve mulching performance and simplify maintenance.
MFZpro Series Product Manual.pdf
Two-Year Warranty
The MFZpro-200 Professional Side-Shift Flail Mower (SKU: VTI-MFZPRO200) has been rigorously tested to withstand tough conditions and includes a two-year warranty on the machine.
Learn More
MFZpro-200 Parts Guide.pdf
| A1(in) | B1(in) | C1(in) | D1(in) | E1(in) | F(in) | G(in) | A2(in) | B2(in) | C2(in) | D2(in) | E2(in) |
|---|---|---|---|---|---|---|---|---|---|---|---|
You May Also Like…
-
MFZpro-155 Flail Mower/Mulcher with Offset
Min 30 PTO HP
CAT I / CAT II
61" Mowing WidthAvailable October 2026
$3,795.00 Read More -
MFZpro-175 Flail Mower/Mulcher with Offset
Min 35 PTO HP
CAT I / CAT II
68" Mowing WidthAvailable October 2026
$3,995.00 Read More -
Limited Offer
MFZpro-220 Flail Mower/Mulcher with Offset
Min 60 PTO HP
CAT I / CAT II
86" Mowing WidthOnly 2 left in stock
$3,395.00 Read More -
MFZpro-135 Flail Mower/Mulcher with Offset
Min 25 PTO HP
CAT I / CAT II
53" Mowing WidthAvailable Spring 2027
$3,595.00 Read More
Proud supporters of the FFA
Very good heavy duty flail at a significantly better price than competing models. Here are my thoughts after about 30 hours of use.
Pros:
1. Arrived in great condition with no missing parts and was easy to assemble.
2. Hydraulic shift works well and I didn’t need a flow reducer valve.
3. On a 65 HP tractor it easily powers through 6′ tall grass. Unless you are cutting large areas of heavy brush, you should be safe at the minimum HP rating for this flail.
Cons:
1. The frame the top-link connects to could use more reinforcement. There is a lot of torque on it when you lift the implement, and you can see in the photo it gets canted to the front. The bolts are tightened as much as they will go without bending the tube.
2. The design of the knives traps clumps of grass on the sides which seem to throw off the balance of the rotor slightly and introduce some minor vibration in the PTO shaft.
3. The steel angle used as a roller scraper on the rear is too thin and positioned too close to the ground, so it bends easily. You MUST lift the unit up when reversing. Be especially careful reversing on steep hills. I hit the ground even at full lift height and badly bent the scraper. Because the top-link attachment point is a slot to allow movement with ground contour and due to the issue in #1 above, even at full lift height the rear end sags quite a bit.
Overall I am happy with the unit, especially considering the price. None of the cons stop me from getting the job done. It’s well suited for a rough cut field maintaining machine and is more compact than a rotary cutter. When cutting very tall grass with thick-stem weeds that get laid over, you will likely need a second pass in the opposite direction to get everything, but I think that would be true of any flail. Just don’t expect to make a single pass and have a perfect finish cut, no matter how slowly you go.